Oxygen in a Hf-bearing refractory host: as-melted pickup from high-purity charge (~0.3 at.%) and a solubility ceiling before HfO₂ that the source states three ways (0.5 / 0.5–1 / 0.8–1.0 at.%) — Nb45Ta25Ti15Hf15 (Huang et al. 2025 preprint) with a feedstock-vs-chamber origin study (Belcher et al. 2025) — materials scout,
What’s claimed and how well supported
- Labels on this page
- STRONG ×19 HYPOTHESIS ×4 WEAK ×8 SPECULATIVE ×6 OPEN ×3 NONE ×10
- Strongest label used
- STRONG
- Main caveat (quoted)
- The Bridge A section comes after the materials and is ◆ SPECULATIVE.
Counted automatically from the labels printed on this page. Counts are a reading aid, not a grade of the page.
Terms on this page (4), plain-language definitions
- Host (matrix)
- Majority element/phase whose lattice dominates the material.
- Dopant
- Intentional dilute impurity meant to tune electronic/optical/catalytic behavior without replacing the host as majority phase.
- Dislocation
- Line defect enabling plastic slip at realistic stresses; edge vs screw are the two classic geometries.
- Valency (ling.)
- Arity: how many actants a predicate takes; formal vs semantic valency can diverge.
Definitions quoted from the Chem for linguists primer glossary.
Date: 2026-11-10 PT (weekday research push, evening)
Status: Materials scout. The metallurgy is same-domain description from the two sources opened below (REAL inside physical metallurgy). Grades, arithmetic and cross-source comparisons are my analysis. The Bridge A section comes after the materials and is SPECULATIVE. Not a correlate. Not a joint field.
Audience: Grant (syntax/semantics; less chemistry). End goal: designing new metal alloys. Takes up open question OQ5 ("Oxygen in the Fe-micro-alloyed hostMajority element/phase whose lattice dominates the material.") of Ti–Zr–Hf–Nb–Ta–Fe baseline (Liu 2022): F2.5-ST ~971 MPa / ~17.5% and aged continuous GB Hf₂Fe §5 (= OQ3 of Ti–Zr–Hf–Nb–Ta with Fe micro-alloying: a ductility window set by nano Hf₂Fe at grain boundaries), and OQ3/OQ4 of Ti–Zr–Hf–Nb–Ta base printed (Yang 2025, EBM): nominal Ti15Zr10Hf40Nb10Ta25, the Fe-free end of the Fe family §5 (what the "Raw material" was; oxygen on tensile specimens), by bounding, not by measuring: no source measures oxygen in the BIT Fe-micro-alloyed Ti-Zr-Hf-Nb-Ta host, and none does tonight.
Sources, stated plainly: (H) Huang, Zhu, Belcher, Rigsby, Apelian, Arróyave & Lavernia, "Predicting interstitial elements in Refractory Complex Concentrated Alloys", arXiv:2512.08080v1 (8 Dec 2025; CC BY 4.0; preprint, not peer-reviewed as posted). (B) Belcher, Kamp, To, Lu, Chassaing, Boll, MacDonald, Lee, Apelian & Lavernia, "The origin and control of interstitial impurities in refractory complex concentrated alloys", J. Alloys Compd. 1010 (2025) 177520, doi:10.1016/j.jallcom.2024.177520 (publisher: CC BY-NC; eScholarship copy labelled CC BY-NC-ND 4.0). Same Texas A&M / UC Irvine circle (Lavernia, Apelian, Belcher on both): one group, not two independent confirmations.
Vocabulary lock kept: Nb, Ta, Ti, Hf (and Zr, Mo, W where named) are principal elements, not dopantsIntentional dilute impurity meant to tune electronic/optical/catalytic behavior without replacing the host as majority phase.. Oxygen, nitrogen, carbon and hydrogen are interstitial impurities ("interstitial impurities" is both sources' phrase); in H oxygen is also added on purpose (via Nb₂O₅), and I keep that as added oxygen, not as "doping" in the semiconductor sense. Fe is not in either source.
Does not: claim that an atom, an impurity, an oxide or a phase is an argument, operator, slot, feature bundle or theta role; supply a chemical stand-in for a theta role; invent numbers or quotes; read numbers off figures (H Figs. 1–13, H Table 1 is an image with no text layer; B Figs. 1–9); give an oxygen level for Liu's Base/F2.5 or Li's HF1/HF2; transfer H's ceiling to the BIT host as a fact; revise Bridge A.
Why this note. Three nights of BIT notes ended with the same gap: no measured oxygen on any Fe-micro-alloyed Ti-Zr-Hf-Nb-Ta specimen (Liu-note OQ5; Fe-note OQ3), and the only BIT oxygen number (Yang 2025, 276 ± 12 mass ppm) is in an undescribed "Raw material" (Nov 9 OQ3). Equiatomic Fe ladders (OQ4) again returned nothing open tonight (§1.2). The most tractable honest step: find an open paper that (i) measures what an arc-melted, Hf-bearing refractory bcc alloy picks up from high-purity charge with no oxygen added, and (ii) says how much oxygen such a host holds before a Hf oxide forms. That bounds the question for the BIT host without pretending to answer it.
The case, in plain words. A Texas A&M / UC Irvine team arc-melts ~30 g buttons of Nb45Ta25Ti15Hf15 (no Zr) from ≥99.95% metals, adding 0, 0.5, 1, 2 or 5 at.% oxygen as Nb₂O₅. With nothing added, the button still holds ~400 mass ppm O (≈ 0.3 at.%). Above about 0.5 at.% the X-ray pattern shows monoclinic HfO₂; at 1 at.% HfO₂ sits on grain boundaries. Every oxygen-added button cracks before 10% cold-rolling reduction. A computer model puts the ceiling at ≥ 0.8 at.%. The same circle's earlier paper (on MoNbTaW, with a NbTiZr comparison) shows that oxygen already in the charge stays in the melt unless something reduces it, and that Ti/Zr-bearing melts pick up more.
What is new (one sentence). In an arc-melted Hf-bearing refractory bcc host made from ≥ 99.95% charge (Nb45Ta25Ti15Hf15), oxygen with nothing added is ~400 mass ppm ≈ 0.3 at.% ( STRONG as stated; my arithmetic gives 0.302), HfO₂ appears in XRD above ~0.5 at.% and on grain boundaries at 1 at.% ( STRONG as stated, figures not read), and every oxygen-added button cracked before 10% rolling reduction ( STRONG as stated), but the paper's solubility ceiling is printed three ways — "0.5 at%", "between 0.5% and 1%", "between 0.8 and 1.0 at.%" — and its computed lower bound of 0.8 at.% does not follow strictly from its own printed numbers (the HfO₂ threshold −10.32 eV lies inside the bracket −10.60 to −10.07 eV that Table 3 gives for μ_O at 0.8%; arithmetic), so the ceiling is WEAK as a single number and STRONG only as a band somewhere between ~0.5 and ~1 at.%; with Belcher et al.'s statement that oxygen "which begins in the feedstocks is not removed" during plasma arc melting without a reducing reaction ( STRONG as stated, for MoNbTaW), the BIT host's oxygen is now bounded by analogy (HYPOTHESIS: ~0.25–0.3 at.% as-melted is the expected scale, about half to a third of the Hf-host ceiling) but its measured value stays NONE; OQ5 narrowed (not closed).
1. Sources
1.1 Opened this run
| Key | Source | How read | Used for |
|---|---|---|---|
| H | Huang, Zhu, Belcher, Rigsby, Apelian, Arróyave & Lavernia, "Predicting interstitial elements in Refractory Complex Concentrated Alloys", arXiv:2512.08080v1 (2025-12-08), CC BY 4.0 (arXiv abs page licence link) | arXiv PDF HTTP 200 (2.06 MB, 23 pp.) → lit/_pdfs/rcca-interstitial-origin/arxiv2512.08080.pdf + arxiv.txt (pdftotext -layout) + arxiv.raw.txt; arxiv-api.xml; openalex-huang.json |
Route and charge (pp. 3–4); baseline O (p. 6); XRD/rolling/fracture (pp. 7–8); ceiling statements (pp. 1, 10, 19–20); oxide enthalpies (Table 2, p. 14); Monte Carlo energies (Table 3, p. 18); μ_O threshold (p. 15) |
| B | Belcher, Kamp, To, Lu, Chassaing, Boll, MacDonald, Lee, Apelian & Lavernia, J. Alloys Compd. 1010 (2025) 177520 | eScholarship PDF (qt0rq5685s) HTTP 200 (6.1 MB, 18 pp. incl. one eScholarship cover page) → belcher2024.pdf + belcher.txt + belcher.raw.txt; openalex-belcher.json (hybrid OA, CC BY-NC). First plain fetch returned HTTP 202 (empty); a second fetch with a browser user-agent returned the PDF — public repository copy, not a login route. Pages below are PDF pages of that copy (journal page = PDF page − 1) |
Charge purity and melt time (p. 4); feedstock-vs-chamber reasoning (p. 11); NbTiZr comparison and Ti/Zr H pickup (p. 13); conclusion on Ti/Hf (p. 16) |
| (cross) | Yang 2025 (Y5), Li 2025 (L5), Liu 2022 (L4), Poulain et al. 2024 (0.27 at.% O equiatomic) — already opened 2026-11-05/06/09 and earlier | Prior captures / notes; not re-fetched | BIT host formula, charge purity, route; equiatomic baseline O |
| (calc) | My arithmetic, standard atomic masses | lit/_pdfs/rcca-interstitial-origin/arithmetic_oxygen.py → arithmetic_oxygen.out |
mass ppm ↔ at.% in four hosts; Table 3 differentials and the μ_O bracket; Hf/O ratios |
Weakness of the copies, stated plainly. H is a Word-made preprint: Table 1 (targeted vs measured O for each button) is an image with no text layer, so the measured O of the 0.5/1/2/5 at.% buttons is NONE here (only the prose "on target, with some deviation up to 0.1 at. % O"); the Monte Carlo constant k (Eq. 1) is not given, so no temperature is attached to Table 3; Fig. 3 (rolled buttons) is not read, so the base alloy's reached reduction is NONE in text. B's two-column layout is captured in belcher.raw.txt; its feedstock and as-cast numbers for NbTiZr are in Fig. 8 only and are not read.
What the sources do not report, stated plainly. Neither has Fe, Zr in the oxygen-ceiling host (H is Zr-free), a heat treatment of the O-added buttons, a tensile test, or anything about Hf₂Fe. Neither measures oxygen in any BIT alloy. H's ceiling is for Nb45Ta25Ti15Hf15 only; its authors write that it "can be further extended to investigate other RCCAs" (future work).
Independence, stated plainly. H and B share authors (Belcher, Apelian, Lavernia) and the same Arc200 plasma arc melter. Agreement between them is continuity, not confirmation. Neither is from the BIT group, so they are independent of L4/L5/Y5.
1.2 Not opened / searched without a hit (do not treat as read)
- OpenAlex
is_oasearches tonight (HfNbTaTiZr / TiZrHfNbTa with boron, Al, Si, Cr, Fe, Mo, C, N,micro-alloying,minor addition;Hf2Fe precipitate high-entropy): Fe hits are only Liu 2022 and Li 2025 again. No equiatomic Fe ladder (OQ4); no micro-addition ladder in equiatomic HfNbTaTiZr found. Not routed around. - Iroc et al. 2022 (Mater. Des. 223: 111239, oxygen-doped TiZrHfNbTa; CC BY-NC-ND per OpenAlex): still abstract only in the corpus; not opened tonight (kept for a later oxygen-dose night).
- Leveau, Ventelon & Clouet 2024 (Acta Mater. 275: 120062, C/N/O at screw dislocationsLine defect enabling plastic slip at realistic stresses; edge vs screw are the two classic geometries. in HfNbTaTiZr; CC BY): title only, not read.
- Cook et al. 2024 (Science 384: 178, NbTaTiHf kink bands; H ref. [17]) and Zhang et al. 2023 (Acta Mater. 245: 118602; H ref. [14]): titles only, not read; nothing taken from them.
2. Sourced materials
2.1 H — host, route, measured oxygen (Nb45Ta25Ti15Hf15)
- Motivation: "In the NbTaTiHf alloy, oxygen sensitivity has not yet been quantified or fully understood." (p. 2)
- Charge: "elemental Nb, Ta, Ti, and Hf slugs, along with Nb₂O₅ lump feedstock (all ≥99.95% purity, metal basis)", Alfa Aesar; ~30 g buttons; arc-melted, "flipped, and re-melted sequentially five times"; chamber evacuated to ~1 × 10⁻⁵ torr and backfilled with ultra-high-purity argon (p. 3, my paraphrase of the base-pressure line).
- Targets: "0, 0.5, 1, 2, and 5 at.% oxygen" (p. 3), keeping "the original atomic fractions of Nb45Ta25Ti15Hf15 in the metal constituent elements" (p. 6).
- Measurement: inert gas fusion, "Triplicate measurements were performed for each alloy composition" (p. 4).
- Result: "The O content in the as-cast NbTaTiHf RCCAs is on target, with some deviation up to 0.1 at. % O. The alloy with no intentionally added O contained approximately 400 ppm O (0.3 at. % O)." (p. 6)
2.2 H — phases, rolling, fracture
- XRD: "In the oxygen-free alloy - which contained a measured baseline oxygen content of ~0.3 at.% - no secondary phases were detected" (p. 7); "in alloys with nominal oxygen concentrations exceeding 0.5 at.%, additional diffraction peaks appeared" (p. 7), matched to monoclinic HfO₂. The Introduction instead says HfO₂ emerges "at oxygen concentrations ≥0.5 at.%" (p. 3). (Exceeding vs ≥: recorded, not resolved.)
- Rolling: room-temperature, ~0.5% per pass; "all oxygen-containing specimens failing before exceeding a 10% reduction in thickness" (p. 8).
- Fracture: "the alloy containing 0.5 at.% oxygen exhibited a partially ductile fracture morphology" (p. 8); STEM/EDS on the 0.5 at.% button shows no grain-boundary O or Hf enrichment (pp. 8–9, prose).
- 1 at.%: "pronounced oxide formation is observed along the grain boundaries" (p. 10), "enriched in Hf and O".
- Consequence: "Due to premature failure during rolling, subsequent microstructural characterization was limited to the as-cast condition" (p. 8).
2.3 H — the ceiling, as printed
| Where | Printed |
|---|---|
| Abstract (p. 1) | "a solubility limit for oxygen between 0.8 and 1.0 at.%, beyond which HfO₂ formation is energetically favorable" |
| §4.1 (p. 10) | "the solubility limit of the system which is estimated to be 0.5 at% (see Section 4.2)" |
| §4.1 (p. 10) | "the solubility limit of oxygen in Nb45Ta25Ti15Hf15 is established to be between 0.5% and 1%" |
| Conclusion (pp. 19–20) | "between 0.8 and 1.0 at%"; (b) "we determined the lower limit of oxygen solubility in the Nb45Ta25Ti15Hf15 RCCA to be 0.8 at%" |
2.4 H — model numbers (printed)
- Oxide formation enthalpies per mole O₂, Table 2 (p. 14, adapted from Hayun et al.): Nb₂O₅ −757, Ta₂O₅ −820, HfO₂ −1108, TiO₂ −941 kJ/mol; "With a formation enthalpy of -1108 kJ/mol, HfO2 is the most stable oxide that may form in the alloy".
- Site preference (MLIP, 500 × 128-atom cells): "The average energy of O decreases with more Ti and Hf neighbors and increases when surrounded by an increasing quantity of Nb or Ta neighbors." (p. 14)
- HfO₂ threshold (p. 15): E(HfO₂) −30.53 eV, E(bcc Hf) −9.88 eV, giving μ_O ≥ −10.32 eV; the authors call it a lower limit, "necessary but not sufficient".
- Table 3 (p. 18), 250 metal atoms + 0/2/4/6 O after 200 MC steps: energies −2539.31, −2560.51, −2580.64, −2598.43 eV; differentials −10.60, −10.07, −8.90 eV per O atom; "0.8%" for 2 O.
2.5 B — where oxygen comes from in plasma arc melting
- Charge: "The commercial purity feedstocks were individual elements, 99.95+ % pure by metals basis" (p. 4); each alloy "molten for a total of ~15 minutes" (p. 4); feedstock interstitials in "ppm (by weight)" (Fig. 1 caption, p. 4).
- Feedstock-to-melt: "the commercial feedstocks started with ~140–250 ppm O" (p. 11); "Without a separate, thermodynamically favorable reaction, such as a reduction reaction, O which begins in the feedstocks is not removed from the RCCAs during PAM." (p. 11); "a broad range was observed from ~120 ppm O up to ~ 320 ppm O in the RCCAs made with commercial purity feedstocks" (p. 11; MoNbTaW).
- Best case: "High purity MoNbTaW RCCAs with as low as 80 ppm O were achieved in this study using high purity feedstocks in a reducing Ar-H2 environment" (p. 13).
- Group IV/V hosts: "transition metals used for RCCAs from subgroup IV and V tend to have much more negative ΔG◦ for O reactions thus stronger thermodynamic drive for absorption" (p. 13). NbTiZr: "Similar trends in the as-cast NbTiZr RCCAs were observed in the MoNbTaW RCCAs, but the magnitude of the content of interstitial impurities in the as-cast RCCAs is significantly higher." (p. 13; numbers only in Fig. 8, not read). In forming gas, NbTiZr "absorbed significant amounts of H interstitial impurities, on the order of 220 ppm H" (p. 13).
- Model limit: "the equilibrium content model was originally developed for pure Nb not non-dilute alloys" (p. 13).
- Design remark (for MoNbTaW): "constituent elements like Ti or Hf which improve O solubility and can scavenge O from the GBs are necessary to further design MoNbTaW based RCCAs." (p. 16)
3. Grades and analysis
| Claim | Grade | Basis |
|---|---|---|
| Nb45Ta25Ti15Hf15 arc-melted from ≥ 99.95% charge, no O added, holds ~400 mass ppm ≈ 0.3 at.% O | STRONG as stated (IGF, triplicate); my conversion 0.302 at.% agrees | H p. 6; arithmetic_oxygen.out [1] |
| O-added buttons on target within 0.1 at.% | WEAK (prose only; Table 1 is an image, values NONE in text) | H p. 6 |
| HfO₂ in XRD above ~0.5 at.% O; GB HfO₂ at 1 at.% | STRONG as stated (figures not read); "exceeding" (p. 7) vs "≥" (p. 3) unresolved | H pp. 3, 7, 10 |
| All O-added buttons crack before 10% rolling reduction | STRONG as stated; base-alloy reduction NONE in text | H p. 8 |
| Single-number O ceiling for Nb45Ta25Ti15Hf15 | WEAK: printed as 0.5, 0.5–1, and 0.8–1.0 at.% in the same paper ( STRONG internal inconsistency, recorded not corrected) | H pp. 1, 10, 19–20 |
| Ceiling somewhere between ~0.5 and ~1 at.% | STRONG as the span covering all three statements and the XRD/STEM observations | H |
| Model lower bound 0.8 at.% follows from Table 3 | WEAK: from Eqs. 6–7 and the printed differentials, −10.60 < μ_O(0.8%) < −10.07 eV; the threshold −10.32 eV (my −10.325) lies inside that bracket, so the printed numbers do not place μ_O(0.8%) below it (arithmetic); the authors' stronger statement may rest on unprinted data | H Table 3, p. 15; arithmetic_oxygen.out [3] |
| "0.8%" = 2 O per 250 metal atoms (0.794 at.% of all atoms) | arithmetic; difference immaterial | arithmetic_oxygen.out [3] |
| O prefers Ti/Hf-rich octahedral sites; HfO₂ most stable oxide | STRONG as computed / tabulated (model; MLIP not fine-tuned) | H p. 14 |
| Feedstock O is not removed in PAM without a reducing reaction | STRONG as the authors' statement for MoNbTaW; WEAK as a general rule (their model is for pure Nb) | B pp. 11, 13 |
| Ti/Zr-bearing NbTiZr picks up more interstitials than MoNbTaW | STRONG as stated; magnitude NONE (figure only) | B p. 13 |
| Oxygen in Liu's Base/F2.5 or Li's HF1/HF2 | NONE (unchanged) | — |
| What Yang's 276 mass ppm "Raw material" was | NONE (unchanged) | — |
Answer to OQ5 of the Liu-baseline note (analysis). Narrowed, not closed. No source measures oxygen in the BIT Fe-micro-alloyed host. What changed: (1) there is now an open, measured as-melted baseline for a Hf-bearing refractory bcc alloy made from ≥ 99.95% charge with nothing added — ~0.3 at.% (H) — which sits with the two numbers already in the corpus: Poulain et al. 2024's equiatomic HfNbTaTiZr base 0.27 at.% (Oxygen in HfNbTaTiZr: measured 0.27 vs 3.24 at.%, stability on ageing) and Yang's 276 mass ppm ≈ 0.245 at.% in the BIT host if the raw material had the nominal composition (Ti–Zr–Hf–Nb–Ta base printed (Yang 2025, EBM): nominal Ti15Zr10Hf40Nb10Ta25, the Fe-free end of the Fe family, WEAK conversion). Three labs, three routes (plasma arc melting as-cast; arc melting + cold rolling + 1373 K anneal; an undescribed "Raw material" before EBM), one scale: ~0.25–0.3 at.% (each STRONG or WEAK as graded in its own note; the clustering is my HYPOTHESIS, not a law). (2) B says charge oxygen stays in an arc melt unless reduced, and Ti/Zr melts take up more. Li 2025 arc-melted from ">99.9 wt.%" metals (Ti–Zr–Hf–Nb–Ta with Fe micro-alloying: a ductility window set by nano Hf₂Fe at grain boundaries), a slightly lower purity than H's ≥ 99.95%. So the expected BIT HF1/HF2 oxygen is at least of the ~0.25–0.3 at.% scale (≈ 300–350 mass ppm in HF1 by arithmetic_oxygen.out [4]): HYPOTHESIS, with a sourced reason in each step, not a measurement.
How close to a Hf-oxide edge? (analysis). H's ceiling is for a host with 15 at.% Hf and no Zr. The BIT host has 40 at.% Hf (36.5 in HF1) and 10 Zr. H's own model says oxygen sits best next to Ti and Hf, and that Hf drives HfO₂. Two opposite readings, neither tested: (a) more Hf gives more Ti/Hf-rich sites, so more oxygen can sit in solution before the oxide (ceiling higher; Hf/O at 0.25 at.% O is ~146–160 in the BIT hosts vs ~50 at H's 0.3 at.% baseline; arithmetic [5]); (b) more Hf gives the oxide an easier source, so HfO₂ comes sooner (ceiling lower). OPEN; H's authors list composition tuning as future work. Design reading (HYPOTHESIS): in the BIT host, iron takes Hf out of the matrix as Hf₂Fe on grain boundaries during ageing (L4, L5), so ageing may change both the Hf left for oxygen and where oxygen sits; any Fe window in this host should carry a measured oxygen before and after ageing (as Fe-note OQ3 already asks), and a deliberate oxygen step at ~0.5 at.% would be the first test of whether this host sits below or above an oxide edge.
What does not transfer (analysis). H's embrittlement is in cold rolling of as-cast buttons, not tension of homogenized, aged specimens; H's base reduction is not stated in text. B's thermodynamics is for MoNbTaW (with a NbTiZr comparison in figure only). Neither says anything about Fe, Hf₂Fe or ageing. The ~0.3 at.% baseline is not a property of the alloy; it is a property of charge + melter + procedure.
Counting rule. Only contradicting data count. H and B are one circle: their agreement is continuity. H's three ceiling statements and the Table 3 bracket are internal to H and are recorded, not used to correct it. Poulain, Yang and H are three labs, but the clustering of their baseline oxygen is mine. No figure digitization. No source counted twice.
SPECULATIVE Cross-domain section. Open after the materials.
4. Bridge A — SPECULATIVE (after the materials)
Bridge A (locked): doping concentration windows and over-doping ↔ valencyArity: how many actants a predicate takes; formal vs semantic valency can diverge., argument saturation and over-arity. Shapes only:
- A floor nobody chose. Even with nothing added, the host carries ~0.3 at.% oxygen from its charge and melter. Shape: a "zero" setting of a window may already be occupied; the window's left edge is the floor the process leaves, not zero. Shape only.
- A ceiling stated three ways. The same paper gives 0.5, 0.5–1 and 0.8–1.0 at.%. Shape: an edge of a window can be known as a band before it is known as a number. Shape only.
- Over the edge, a new thing forms. Past the ceiling the extra oxygen leaves solution as a new phase (HfO₂) that takes one principal element with it. Shape: excess beyond capacity can be expelled into a separate structure that pulls on the frame. Shape only; no oxide is an argument.
- Still continuous. at.%, mass ppm and eV are continuous amounts; the lock "continuous wt% ≠ discrete arity" holds; nothing here counts slots.
Bridge A pressure: none that forces revision. Bridge A unrevised. No chemical stand-in for a theta role, slot or feature bundle; not a correlate; not a joint field. Merge/Agree not involved. No Navajo remark tonight. (Grant's dropped 2026-11-02 "roles not words" theory is not reported as open.)
5. Open questions
- Measured O in the BIT host. Still the real gap (Liu-note OQ5, Fe-note OQ3): IGF oxygen on Base/F2.5/HF1/HF2 as-solutionized and aged.
- Which way does Hf push the ceiling? More Ti/Hf-rich sites (higher) vs an easier HfO₂ source (lower) in a 40 at.% Hf, 10 at.% Zr host (§3). Needs an oxygen step in that host, or H's workflow run on it. Reframed (not answered) by Carbon micro-addition and grain-boundary oxide in a Hf-bearing host: a tensile threshold between 0.4 and 0.6 at.% C (Nb44Ta44Hf10W2) (2026-11-11 evening): in arc-melted Nb44Ta44Hf10W2 (Shen et al. 2025 preprint, CC BY) grain-boundary HfO₂ grown from the last liquid is already present at 0.09 at.% overall O ( STRONG as observed), so a solid-solubility ceiling and an as-cast solidification edge are different numbers ( HYPOTHESIS as a rule); the Hf direction stays OPEN.
- H's ceiling as one number. Which statement is the authors' result (0.5; 0.5–1; 0.8–1.0)? Does unprinted data close the Table 3 bracket around −10.32 eV? Is there a later version of arXiv:2512.08080 or a journal version?
- H Table 1. The measured O of the 0.5/1/2/5 at.% buttons (image only in v1).
- NbTiZr pickup magnitude. B Fig. 8 numbers in a text form (supplement?) would give a Ti/Zr-bearing analog of the BIT host. Answered by substitution in How much oxygen the route puts into equiatomic HfNbTaTiZr: a measured ladder from 0.12 to 1.07 wt.% across powder routes (2026-11-13 evening): Málek et al. 2019 (Materials 12: 4022, CC BY) tabulate gas-fusion oxygen in equiatomic HfNbTaTiZr (Ti + Zr) by powder route, 0.12 ± 0.02 wt.% (atomized + SPS, ≈ 0.88 at.%) to 1.07 ± 0.10 wt.% (ball-milled, ≈ 7.4 at.%) ( STRONG as tabulated); arc-melt pickup in a Ti/Zr host in text form still NONE.
- Carried: Nov 9 OQ1–OQ3, OQ5 (Ti–Zr–Hf–Nb–Ta base printed (Yang 2025, EBM): nominal Ti15Zr10Hf40Nb10Ta25, the Fe-free end of the Fe family); Liu-note OQ2–OQ4; Fe-note OQ1 (no open equiatomic Fe ladder found again tonight), OQ2, OQ5; OQ1–OQ4, OQ6 of HfNbTaTiZr between 550 and 1000 °C: where the unstable band ends (two edges, not one); prior carried stack listed there.
6. Separation
SOURCED (inside metallurgy)
H: Nb45Ta25Ti15Hf15 by plasma arc melting from ≥ 99.95% charge (+ Nb₂O₅), five remelts, Ar backfill; 0/0.5/1/2/5 at.% O targets; IGF triplicate; no-O-added button ~400 ppm ≈ 0.3 at.%; on target within 0.1 at.%; HfO₂ in XRD above ~0.5 at.% (p. 7) / ≥ 0.5 (p. 3); GB HfO₂ at 1 at.%; all O-added buttons crack before 10% rolling reduction; 0.5 at.% partially ductile fracture; ceiling printed as 0.5, 0.5–1 and 0.8–1.0 at.%; oxide enthalpies (Table 2); O prefers Ti/Hf neighbours; HfO₂ threshold −10.32 eV; Table 3 energies and differentials. B: 99.95+ % commercial charge, ~15 min molten; feedstock O ~140–250 ppm; feedstock O not removed without a reducing reaction; MoNbTaW 120–320 ppm (commercial charge), 80 ppm best (Ar-H₂); group IV/V stronger drive; NbTiZr "significantly higher"; ~220 ppm H in NbTiZr in forming gas; model for pure Nb; Ti/Hf scavenging remark.
ANALYSIS (mine, beside the sources)
The grades; mass ppm ↔ at.% conversions; the Table 3 bracket check; the three-statement inconsistency; the ~0.25–0.3 at.% baseline clustering across three labs (HYPOTHESIS); the BIT expected-floor estimate (HYPOTHESIS); the two opposite Hf readings (OPEN); design readings; counting (one circle).
SPECULATIVE
§4 (Bridge A shapes).
Not claimed
No chemical correlate. No chemical stand-in for a theta role, a feature bundle or a slot. Not a joint field. Bridge A unrevised. No number read off a figure or an image table. No oxygen value for the Fe-micro-alloyed host. No transfer of H's ceiling to the BIT host as a fact. Nothing from the not-opened list. The dropped roles-not-words theory is not treated as open.
7. Verdict
Is oxygen in the Fe-micro-alloyed Ti-Zr-Hf-Nb-Ta host known? No — but now bounded. An arc-melted Hf-bearing refractory bcc host from ≥ 99.95% charge carries ~0.3 at.% O with nothing added ( STRONG, H), matching the ~0.25–0.27 at.% already in the corpus for other labs' hosts (clustering HYPOTHESIS); charge oxygen is not removed in arc melting without a reducing reaction ( STRONG as stated for MoNbTaW, B). In that host HfO₂ appears above ~0.5 at.% and rolling fails at every added level ( STRONG as stated), while the single-number ceiling is WEAK (printed three ways; the model bracket straddles its own threshold — arithmetic). The BIT host's measured oxygen stays NONE; whether its 40 at.% Hf raises or lowers the ceiling is OPEN. OQ5 narrowed; OQ4 again no open source. Bridge A unrevised; shapes only, after the materials.
v0 — 2026-11-10 PT, evening. Pointers added: corpus-reading-order row; CONCLUSIONS-v1-addendum paragraph; site-content-map (inventory, slug, near-ready, Path E page row); back-pointers at tizrhfnbta-fe-liu2022-baseline §5 OQ5 and tizrhfnbta-base-composition-ebm §5 OQ4 (+ footers). Quotes machine-checked against the captured text (lit/_pdfs/rcca-interstitial-origin/check_quotes_oxygen.py); arithmetic in lit/_pdfs/rcca-interstitial-origin/arithmetic_oxygen.py. Speculation flagged. Bridge A lock unrevised. No joint field. Back-pointer added 2026-11-11 evening: §5 OQ2 → Carbon micro-addition and grain-boundary oxide in a Hf-bearing host: a tensile threshold between 0.4 and 0.6 at.% C (Nb44Ta44Hf10W2). Back-pointer 2026-11-13: §5 OQ5 answered by substitution in How much oxygen the route puts into equiatomic HfNbTaTiZr: a measured ladder from 0.12 to 1.07 wt.% across powder routes.
Corpus note: nbtatihf-oxygen-solubility-pickup-v0.md. The metallurgy is same-domain description from the two sources the note lists as opened: Huang, Zhu, Belcher, Rigsby, Apelian, Arróyave & Lavernia 2025 (arXiv:2512.08080v1, CC BY 4.0; a preprint), the arXiv PDF read through its text layer, and Belcher et al. 2025 (J. Alloys Compd. 1010: 177520; CC BY-NC per the publisher, CC BY-NC-ND on the eScholarship copy that was read). Both are from one Texas A&M / UC Irvine circle, so their agreement is continuity, not confirmation. Figures were not digitized and the preprint's Table 1 is an image with no text layer, so no number is read off a figure or an image. Quotes are verbatim and machine-checked; conversions (mass ppm to at.%) and the check of the preprint's Table 3 energies are the note's own arithmetic in a script beside the capture. The host is Nb45Ta25Ti15Hf15 (no Zr, no Fe); it is not the Beijing Institute of Technology Ti–Zr–Hf–Nb–Ta host, and its oxygen ceiling is not transferred to that host as a fact. No oxygen level is given for the Fe-micro-alloyed host. The grades (STRONG / WEAK / NONE / OPEN / HYPOTHESIS) and the comparisons between sources are analysis, not a declared correlate. The Bridge A section comes after the materials and is speculative. No chemical stand-in for a theta role or a slot. Bridge A unrevised. Not a joint field.