No joint field · Bridge A = SPECULATIVE pedagogy

Labels: SOURCED HYPOTHESIS SPECULATIVE OPEN NONE (REAL = same-domain materials or linguistics, shown like SOURCED)

Path E · Materials scout (HfNbTaTiZr after 96 h at 550–1000 °C: where the bcc split and the hcp stop)

HfNbTaTiZr between 500 and 1000 °C: where the unstable band ends — single bcc after 96 h at 1000 °C, peak splitting at 900 °C, two bcc + hcp at 550 and 700 °C (vacuum-sealed anneals; oxygen not measured) — materials scout,

What’s claimed and how well supported

Labels on this page
STRONG ×17 HYPOTHESIS ×8 WEAK ×9 SPECULATIVE ×6 NONE ×6
Strongest label used
STRONG
Main caveat (quoted)
The Bridge A section comes after the materials and is ◆ SPECULATIVE.

Counted automatically from the labels printed on this page. Counts are a reading aid, not a grade of the page.

Terms on this page (8), plain-language definitions
Dopant
Intentional dilute impurity meant to tune electronic/optical/catalytic behavior without replacing the host as majority phase.
Solute
Intentional minority species dissolved in the host (alloying addition).
Dislocation
Line defect enabling plastic slip at realistic stresses; edge vs screw are the two classic geometries.
Precipitate
Second-phase particle that forms (often on aging) and blocks dislocations.
BCC
Body-centered cubic — Fe/steel common; plasticity more temperature-sensitive.
HCP
Hexagonal close-packed — fewer primary slip systems; Mg, Ti, Zn often anisotropic.
Solid solution
Solute atoms dissolved into the host lattice (substitutional or interstitial) without a separate precipitate phase.
Valency (ling.)
Arity: how many actants a predicate takes; formal vs semantic valency can diverge.

Definitions quoted from the Chem for linguists primer glossary.

Date: 2026-11-04 PT (weekday research push, evening)
Status: Materials scout. The metallurgy is same-domain description from the sources opened below (REAL inside physical metallurgy). Grades and cross-source comparisons are my analysis. The Bridge A section comes after the materials and is SPECULATIVE. Not a correlate. Not a joint field.
Audience: Grant (syntax/semantics; less chemistry). End goal: designing new metal alloys. Takes up open question OQ3 ("The upper edge of the unstable band") of HfNbTaTiZr at 873 K: nanoscale hcp and a stress rise in one batch (compression only) §5, in part: one of the two primary papers named there (Chen et al. 2019) opened in full as the accepted manuscript on OSTI, plus the abstract of the other (Yasuda et al. 2021, OQ4), whose body was blocked tonight. It does not touch tension (OQ1 of that note stays open).
Sources, stated plainly: (1) Chen, Tong, Tseng, Yeh, Poplawsky, Wen, Gao, Kim, Chen, Ren, Feng, Li & Liaw, "Phase transformations of HfNbTaTiZr high-entropy alloy at intermediate temperatures", Scripta Materialia 158 (2019) 50–56, as the authors' accepted manuscript on OSTI (DOE public access). It is an X-ray, SEM, TEM and atom-probe phase study: no mechanical test, no oxygen, nitrogen or carbon analysis, and the manuscript copy has no Tables 1–4 in it (they are cited in the text but not present). (2) The abstract only of Yasuda, Yamada, Cho & Nagase, Mater. Sci. Eng. A 809 (2021) 140983 (CC BY), as served by OpenAlex; the publisher page was blocked to both fetch routes and no repository copy exists (§1.2).
Vocabulary lock kept: Hf, Nb, Ta, Ti, Zr are principal elements, not dopantsIntentional dilute impurity meant to tune electronic/optical/catalytic behavior without replacing the host as majority phase. (Doping vs alloying vocabulary). Oxygen is an interstitial soluteIntentional minority species dissolved in the host (alloying addition).; in C2 it is not measured.
Does not: claim that an oxygen atom, a precipitateSecond-phase particle that forms (often on aging) and blocks dislocations., a phase, a temperature or a dislocationLine defect enabling plastic slip at realistic stresses; edge vs screw are the two classic geometries. is an argument, operator, slot, feature bundle or theta role; supply a chemical stand-in for a theta role; invent numbers or quotes; read numbers off figures or XRD patterns; claim an oxygen level for C2's or Yasuda's alloy; claim anything about strength or ductility from a phase study; revise Bridge A.

Why this note. Last night's note mapped the clean alloy as unstable in a ~500–800 °C band and stable at 900 °C (from P1, clean argon), and asked where the band's upper edge is for low-oxygen material, naming Yasuda et al. 2021 and Chen et al. 2019 as the primary papers. Chen et al. 2019 turned out to be openable (OSTI). It is the one paper in the set that holds one starting state and anneals it at a ladder of temperatures for the same time, so it places edges directly. It also shows that one widely cited restatement of it (in P1) rounds its 900 °C result to the stable side.

The case, in plain words. Cold-rolled sheets of the five-metal alloy are made one phase by 10 min at 1200 °C and a water quench. Pieces are then sealed in evacuated quartz tubes and held for 96 h at 550, 700, 900 or 1000 °C. At 1000 °C the alloy stays one bcc phase. At 900 °C its X-ray peaks split: it has begun to separate. At 700 °C and 550 °C it has become three phases: the old bcc, a niobium–tantalum-rich bcc, and a zirconium–hafnium-rich hexagonal (hcp) phase. At 700 °C, things start within 2.5 h, at the grain boundaries first, and by 96 h about two fifths of the volume is precipitate.

What is new (one sentence). In equiatomic HfNbTaTiZr homogenized at 1200 °C / 10 min and water quenched (Chen et al. 2019, OSTI accepted manuscript), 96 h anneals in vacuum-sealed quartz leave "only a single BCCBody-centered cubic — Fe/steel common; plasticity more temperature-sensitive. phase" at 1000 °C ( STRONG as observed by synchrotron XRD), make "the BCC phase" "unstable by showing peak splitting" at 900 °C ( STRONG as observed; which phases form at 900 °C is NONE in the capture, Table 1 being absent), and give two BCC phases plus one HCPHexagonal close-packed — fewer primary slip systems; Mg, Ti, Zn often anisotropic. phase at 550 and 700 °C ( STRONG; HCP Zr–Hf-rich with a Burgers orientation relationship by SAED at 700 °C), with grain-boundary precipitates after 2.5 h at 700 °C and ~41 vol.% precipitates after 96 h ( STRONG as stated); together with Yasuda et al. 2021's abstract (two-bcc split at 773–1073 K, hcp at 773–973 K; WEAK here, abstract only) this puts the upper edge of the bcc-split band between 900 and 1000 °C and the upper edge of hcp formation near 700–800 °C in two independent labs (WEAK→STRONG as a bracket; edges not pinned), oxygen is NONE in both, and C2's vacuum-quartz 900 °C splitting versus P1's clean-argon 900 °C stability is an unresolved tension that oxygen pickup could explain ( HYPOTHESIS, following P1's own vacuum result).


1. Sources

1.1 Opened this run

Key Source How read Used for
C2 Chen, Tong, Tseng, Yeh, Poplawsky, Wen, Gao, Kim, Chen, Ren, Feng, Li & Liaw, "Phase transformations of HfNbTaTiZr high-entropy alloy at intermediate temperatures", Scripta Materialia 158 (2019) 50–56, doi:10.1016/j.scriptamat.2018.08.032 Accepted manuscript on OSTI, www.osti.gov/servlets/purl/1504430 (OSTI ID 1504430; found via OpenAlex locations; HTTP 200, 2.1 MB, application/pdf, 20 pages, UT-Battelle/DOE public-access header) → lit/_pdfs/hea-phase-chen2019/chen2019-osti-1504430.pdf + .txt (layout) + .raw.txt Route, anneal ladder (550–1000 °C / 96 h; 700 °C / 2.5–192 h), phases by temperature, time series at 700 °C, lattice parameters, volume fractions, orientation relationship, the authors' CALPHAD restatement and entropy argument
Y21-abs Yasuda, Yamada, Cho & Nagase, "Deformation behavior of HfNbTaTiZr high entropy alloy singe crystals and polycrystals" (title as published), Mater. Sci. Eng. A 809 (2021) 140983, doi:10.1016/j.msea.2021.140983 (CC BY) Abstract only, reconstructed from the OpenAlex abstract_inverted_index → lit/_pdfs/hea-phase-chen2019/yasuda2021-abstract-openalex.txt (+ the OpenAlex JSON) Temperature ranges of the two-bcc split, hcp and ω; the yield-stress anomaly in words
(re-used) P1 (Poulain et al. 2024) and Z1-abs, lit/_pdfs/hea-oxygen-hfnbtatizr/; Y4 (Yasuda et al. 2025), lit/_pdfs/hea-hcp-yasuda2024/ Captures only P1's restatement of C2 and its vacuum vs argon result; Y4's 1073 K remark

Weakness of the copy, stated plainly. C2 on OSTI is the accepted manuscript, not the typeset version. Its text cites Tables 1–4 (phases by temperature, phase compositions by TEM-EDS and APT, VEC/size and mixing-enthalpy tables), but the tables are not in the file (text extraction and the image list show only Figures 1–4 and the graphical abstract). So the phase list at 900 °C, and every phase composition, is not in this note. The XRD patterns are figures; no number in this note comes from a figure. The manuscript has small typing slips that I quote around rather than correct (e.g. "Na and Ta" where Nb is meant; "8 192 h").

What the sources do not report, stated plainly. C2: no oxygen, nitrogen or carbon content; no purity of the starting metals; no strength, hardness or ductility; no anneal at 800 °C; no anneal longer than 96 h except at 700 °C. Y21-abs: no oxygen; ranges given without the anneal times.

Independence, stated plainly. C2 (Tennessee, Tsing Hua, ORNL, Argonne, NETL, IIT) shares no author with Y4/Y21 (Osaka, Hyogo), P1/Z1 (Laplanche, Li et al.), L2/J1 (Lu, Wu, Lei et al.) or L3 (Larianovsky et al.). P1 cites C2 (its ref. [27]); Y4 cites C2 (its ref. [15]); C2 cites neither (it predates them).

1.2 Not opened (do not treat as read)

  • Yasuda et al. 2021 body (Y21): ScienceDirect HTTP 403 to curl; the fetch tool HTTP 400 on the same page; doi.org resolves to the Elsevier linking hub only; OpenAlex and Unpaywall list the publisher as the only open location (has_repository_copy: false); an Osaka repository search returned no matching item. Not routed around. A search-engine snippet of the blocked page suggests the body also has room-temperature tension after 24 h anneals at 673–1073 K; that is not opened, not used, and no number from it is in this note — it is the lead for OQ1 next time.
  • Stepanov et al. 2018 (Mater. Lett. 211: 87–90) and Schuh et al. 2018 (Acta Mater. 142: 201–212, nanocrystalline HfNbTaTiZr and the CALPHAD diagram): used only as C2 restates them.
  • Senkov et al. 2018 (Metall. Mater. Trans. A 49: 2876–2892, cold deformation, 800 °C anneals): used only as C2 restates it.
  • Zhao et al. 2025 body (Z1): not retried (blocked Oct 30 and Nov 2). Not routed around.
  • ~~Li et al. 2025~~ (Materials 18: 1463): recorded as a lead here; opened 2026-11-05 in Ti–Zr–Hf–Nb–Ta with Fe micro-alloying: a ductility window set by nano Hf₂Fe at grain boundaries (Europe PMC XML / PMC11989734).

2. Sourced materials (C2, Y21-abs)

2.1 Alloy and route (C2)

  • Making: "The HfNbTaTiZr buttons were prepared by arc-melting in an argon atmosphere", cut to slabs and "cold-rolled to a final thickness of 4 mm (a total reduction of ~ 70%)".
  • Homogenizing: the sheets "were then sealed in vacuum-quartz tubes and then homogenized at 1,200 °C for 10 min., followed by water quenching".
  • Ladder: "The as-homogenized alloys were subsequently annealed at (550 – 1,000 ℃) for 96 h or at 700 ℃ for 2.5 h, 96 h, and 192 h".
  • Starting state: "The homogenized sample has a single BCC phase with a lattice constant of 3.408 Å", with "a homogeneous distribution of composition" by EDS mapping.
  • Aim, in the authors' words: to clarify a "Controversy" over "the phase stability of the HfNbTaTiZr RHEA at intermediate temperatures of 500 – 900 °C".

2.2 Phases by temperature, 96 h (C2)

  • 1000 °C: "For the sample annealed at 1,000 ℃, only a single BCC phase was found."
  • 900 °C: "When annealed at 900 ℃, the BCC phase becomes unstable by showing peak splitting." (The phases are "summarized in Table 1", which is not in the copy.)
  • 700 and 550 °C: "Multiple phases were observed at 550 and 700 ℃, which were confirmed as two BCC phases and one HCP phase".
  • 550 vs 700 °C: at 550 °C "several minor peaks corresponding to the BCC matrix disappear"; later, the residual-matrix peaks at 550 °C "become weak with only one major peak existing".

2.3 Time series at 700 °C (C2)

  • 2.5 h, XRD: "a major BCC phase and another minor BCC phase (confirmed as Ta-Nb-rich BCC phase later)"; APT: "a major BCC phase with a small amount of Ta-Nb-rich and Hf-Zr-rich precipitates".
  • 2.5 h, SEM: "precipitates with an irregular morphology formed along the grain boundaries, with the volume fraction of about 3.23%".
  • 96 h: "precipitates with a lamellar shape were formed along grain boundaries and meanwhile round-shape precipitates were developed within grains, with increasing total volume fraction of about 41.2%".
  • 192 h: coarsening within grains and a change at grain boundaries "from the lamellar to spherical shapes"; "The total volume fraction of precipitates is about 39.8%."
  • 96 and 192 h, XRD: "three phases are formed, identified as two major BCC phases and one minor HCP phase", with BCC1 "3.447 Å" and BCC2 "3.323 Å", HCP "a = 3.143 Å and c = 5.042 Å".
  • Phases by STEM-EDS (96 h, grain interior): "the Ta-Nb-rich phase", "the Hf-Zr-rich phase", and "the phase with almost evenly-distributed elements" (the matrix).
  • HCP crystallography: SAED confirms "a Hf-Zr-rich HCP phase", with "a classical Burgers orientation relationship (OR)".
  • Conclusion, in the authors' words: the alloy "decomposes into three phases, the BCC matrix, BCC Ta-Nb-rich and HCP Zr-Hf-rich precipitates when annealing at 700 °C even after a short-period of annealing time, 2.5 h".

2.4 Calculation and the authors' reading (C2)

  • CALPHAD (restated from Schuh et al. [12]): it "predicts the formation of a single BCC solid-solution phase in a temperature range from 1,020 to 1,200" °C; at 1,020 °C a Nb–Ta-rich BCC "starts to precipitate", and an HCP phase "mainly consisting of Hf, Ti, and Zr starts to form at 800" °C; so "below 1,020" °C "the single BCC phase is no longer thermodynamically stable".
  • Mismatch named by the authors: "some disagreements exist between the CALPHAD calculations [12] and the present experiments at 550 and 700" °C, and "the annealing time may be too short to reach the equilibrium state".
  • Earlier work restated: Senkov et al. saw "two BCC phases" after "annealing a cold-rolled HfNbTaTiZr RHEA at 800 °C for 2 h"; Stepanov et al. "reported the formation of two phases with hexagonal-closed-packed (HCP) and BCC structures after annealing a homogenized HfNbTaTiZr at 800 °C for 100 h".
  • Why (authors' reading): Ti, Zr and Hf are HCP at low temperature and BCC at high; Nb and Ta stay BCC; and as temperature falls "the free energy of the fully-random solid solutionSolute atoms dissolved into the host lattice (substitutional or interstitial) without a separate precipitate phase. of the equiatomic composition is raised, relative to other non-equiatomic compositions".

2.5 Yasuda et al. 2021, abstract only (Y21-abs)

  • Ranges: "At 773–1073 K, phase separation into two bcc phase took place, while the hexagonal close-packed (hcp) phase was precipitated at 773–973 K." Also: "The ω phase which is typical in β-titanium alloys was also observed at 673 K."
  • Strength in words: "The yield stress decreased rapidly with increasing temperature up to 673 K, while the stress increased at 873 K."
  • Cause, in the authors' words: "the dynamic precipitation of the hcp phase is responsible for the yield stress anomaly".

3. Grades and analysis

Claim Grade Basis
After 1200 °C / 10 min + water quench the alloy is single bcc, a = 3.408 Å STRONG as observed (synchrotron XRD, EDS map) C2
96 h at 1000 °C: single bcc STRONG as observed (synchrotron XRD; one condition) C2
96 h at 900 °C: bcc peak splitting (decomposition begun) STRONG as observed; the phase list at 900 °C NONE in the capture (Table 1 missing) C2
96 h at 550 and 700 °C: two bcc + one hcp STRONG (XRD; TEM/SAED/EDS at 700 °C) C2
At 700 °C precipitation starts at grain boundaries within 2.5 h (~3.23 vol.%), ~41.2 vol.% after 96 h, ~39.8 vol.% after 192 h STRONG as stated (SEM image fractions; method not detailed) C2
HCP present after 2.5 h at 700 °C WEAK: the conclusion says three phases at 2.5 h, but the 2.5 h XRD shows two bcc only and APT gives compositions, not structure C2
Zr–Hf-rich HCP in a Burgers OR with the matrix STRONG locally (SAED; P1 notes no statistics in C2 and later confirms the Burgers OR as the major one) C2, P1
CALPHAD: single bcc 1020–1200 °C, Nb–Ta bcc below 1020 °C, HCP below 800 °C WEAK (restated calculation) C2 restating Schuh et al.
Two-bcc split at 773–1073 K, hcp at 773–973 K, ω at 673 K WEAK here (abstract only; anneal times not given) Y21-abs
Oxygen in C2's or Y21's alloy NONE (not measured or not available) —

Answer to OQ3 of the Nov 3 note (analysis), in part. OQ3 asked where, between 873 K (hcp forms; Y4) and 1173 K (P1: clean alloy single bcc for 1000 h), the hcp stops forming for low-oxygen material. Two independent labs now bracket two different edges: - Edge of the bcc split. C2: split at 900 °C, none at 1000 °C (96 h). Y21-abs: split up to 1073 K (800 °C). So in both labs the two-bcc split reaches at least 800 °C, and in C2 it reaches 900 °C but not 1000 °C ( STRONG for C2's bracket as observed; WEAK→STRONG as a two-lab agreement in kind). The CALPHAD restatement puts the start of the Nb–Ta bcc at 1020 °C ( WEAK), which fits C2's bracket. - Edge of hcp formation. Y21-abs: hcp up to 973 K (700 °C), not at 1073 K (800 °C); Y4 says the same for 1073 K (restated). C2: hcp at 700 °C; at 900 °C the prose names only peak splitting. So the hcp edge is near 700–800 °C in Yasuda's material ( WEAK, abstract), and C2 does not show hcp above 700 °C in its prose ( NONE for 900 °C, Table 1 missing). The CALPHAD restatement says 800 °C ( WEAK). Stepanov et al.'s 800 °C / 100 h HCP + BCC (restated in C2, WEAK) sits right at that edge. So the band from last night's map splits in two: a bcc-split band up to somewhere between 900 and 1000 °C and an hcp band up to about 700–800 °C. Last night's unstable band of 500–800 °C was the hcp band; the split band reaches higher (analysis; brackets, not pinned edges; no oxygen measured in either lab).

The 900 °C tension with P1 (analysis). P1 aged its clean alloy (0.27 at.% O measured) at 900 °C for 1000 h in argon-filled quartz and found it "remain single-phase BCC" (twice); the same alloy aged under vacuum picked up interstitials and decomposed. C2 annealed in "vacuum-quartz tubes" and found peak splitting at 900 °C after only 96 h. Three readings: (a) C2's sample picked up oxygen in the vacuum tube, as P1's vacuum sample did ( HYPOTHESIS; C2 measures none; P1's own discussion says discrepancies between labs "may be related to the presence of oxygen"); (b) C2's starting state differs (cold-rolled, 10 min at 1200 °C, finer grains — P1 restates C2's grain size as "5 µm < grain size < 60 µm") and nucleates faster ( HYPOTHESIS); (c) the true clean edge is near 900 °C and small differences decide it ( HYPOTHESIS). C2 alone cannot choose. Counting rule: this is a real disagreement in kind at one temperature but with different atmospheres, times and starting states, and one side has no oxygen measurement, so it is not counted as a contradiction of P1; it is carried as an open tension (§5).

A restatement check (analysis). P1 restates C2 as finding the alloy "to decompose below 900" °C and "a stable single-phase solid solution above 900" °C. C2's own text puts 900 °C itself on the unstable side (peak splitting). The restatement is fair for "above 900 °C" (1000 °C single bcc) but rounds 900 °C away; using C2 through P1 would have hidden the tension above ( STRONG as a text comparison of two captures).

How fast (analysis, across sources). C2: at 700 °C grain-boundary precipitates within 2.5 h, and two fifths of the volume within 96 h ( STRONG). Y4: at 600 °C hardness high within 0.2 h and a measurable change within an 1800 s hold ( STRONG, Nov 3). Two labs, two temperatures, the same message: inside the band the alloy changes in minutes to hours, not only over thousands of hours ( STRONG in kind). C2's grain-boundary-first sequence also matches the grain-boundary bcc2 that Y4 restates for polycrystals and the boundary-heavy HCP in L3 after a slow cool ( HYPOTHESIS as one mechanism; different states).

Design-relevant reading (analysis). (1) For a single-bcc HfNbTaTiZr part, the safe holding band in these data starts at 1000 °C (C2, 96 h; P1 adds 900 °C clean under argon) ( STRONG at 1000 °C for C2's conditions; 900 °C depends on atmosphere, HYPOTHESIS on cause). (2) Cooling must be fast from 1000 °C down through 900–500 °C, not only through 800–500 °C as last night's note suggested; the split band reaches 900 °C ( HYPOTHESIS for practice, from C2's 900 °C result). (3) Anneal in argon with a getter, not in vacuum, and report oxygen before and after (P1's vacuum result; C2's tube atmosphere is the open variable). (4) A 1000 °C / 96 h single-bcc result with a measured oxygen level, and a 900 °C / 96 h anneal under argon on C2-type cold-rolled material, would settle the 900 °C tension.

Counting rule. Only contradicting data count. C2 agrees with Y21-abs on the split band reaching 800 °C and on hcp at 700 °C (agreement in kind, two labs; Y21 abstract-only, so counted once as WEAK support). C2 vs P1 at 900 °C: not counted (above). C2 vs Stepanov (restated) at 800 °C: no C2 data at 800 °C; nothing counted. C2 vs CALPHAD: authors name a mismatch at 550/700 °C (three phases vs two predicted) and put it down to non-equilibrium; not counted against anything here. No source counted twice.


SPECULATIVE Cross-domain section. Open after the materials.

4. Bridge A — SPECULATIVE (after the materials)

Bridge A (locked): doping concentration windows and over-doping ↔ valencyArity: how many actants a predicate takes; formal vs semantic valency can diverge., argument saturation and over-arity. Shapes only:

  • Two edges, not one. What looked like one band of trouble is two nested ones: one change (the split into two solutions) reaches higher than the other (a new structure forming). Shape: a combination can stop being one unit in a first, milder way before a second, sharper way; where the window ends depends on which change you count. Shape only.
  • An edge that may move with what gets in. The same nominal setting (900 °C) gives one phase in a sealed, clean hold and a split in another lab's vacuum tube. Shape: an edge read off one run may be the edge for that run's unmeasured extra content, not for the stated contents. Shape only.
  • A restatement that rounds. A cited summary put the borderline case on the safe side. Shape: when the edge is the point, read the edge case in the primary. Shape only.
  • Still continuous. Temperatures, times, lattice parameters and volume fractions are continuous amounts; the lock "continuous wt% ≠ discrete arity" holds; nothing here counts slots. No dose is varied tonight (C2 varies temperature and time), so no window edge in concentration is placed.

Bridge A pressure: none that forces revision. Bridge A unrevised. No chemical stand-in for a theta role, slot or feature bundle; not a correlate; not a joint field. Merge/Agree not involved. No Navajo remark tonight.


5. Open questions

  1. The 900 °C tension, settled. One starting state annealed 96 h at 900 °C under argon with a getter and under vacuum, with oxygen measured before and after. Would say whether C2's 900 °C split is the clean edge or contamination (P1 says the latter is possible at 900 °C).
  2. Phases at 900 °C. C2's Table 1 (absent from the manuscript copy) lists them; the typeset version is not open here. Is there hcp at 900 °C or only two bcc?
  3. The hcp edge, primary. Y21's body (blocked tonight) gives the anneal times behind the hcp range of 773–973 K; an 800 °C anneal of C2-type material would test Stepanov et al.'s 800 °C / 100 h HCP against Y21's no-hcp at 1073 K.
  4. Tension after intermediate anneals (carried OQ1 of the Nov 3 note). Y21's body appears to have room-temperature tension after 24 h anneals at 673–1073 K (search snippet only, not opened); an open copy would answer OQ1 directly.
  5. ~~A real dopant window in this family.~~ Answered 2026-11-05 in Ti–Zr–Hf–Nb–Ta with Fe micro-alloying: a ductility window set by nano Hf₂Fe at grain boundaries (Li et al. 2025 opened): Fe micro-alloying of non-equiatomic Ti₁₅Zr₁₀Hf≈₃₆Nb₁₀Ta₂₅ gives a sourced elongation span ~2.65–19% at ~955–1081 MPa; equiatomic transfer still NONE; oxygen NONE.
  6. Carried: OQ1, OQ2, OQ4 of HfNbTaTiZr at 873 K: nanoscale hcp and a stress rise in one batch (compression only); OQ1, OQ2, OQ4 of HfNbTaTiZr after hot isostatic pressing: an HCP phase and no tensile stretch; OQ1–OQ3 of Oxygen in HfNbTaTiZr: measured 0.27 vs 3.24 at.%, stability on ageing; OQ2–OQ4 of Oxygen in a Ta-bearing five-element alloy: one measured tensile pair; OQ2 of Where added oxygen stops helping ductility: a tensile ladder in Ti–Zr–Nb; OQ1/OQ4 of Oxygen added on purpose: a dose window in refractory high-entropy alloys.

6. Separation

SOURCED (inside metallurgy)

C2: equiatomic HfNbTaTiZr, arc-melted under argon, cold-rolled ~70%, homogenized 1200 °C / 10 min in vacuum-sealed quartz, water quenched → single bcc, a = 3.408 Å; 96 h anneals: 1000 °C single bcc, 900 °C bcc peak splitting, 550 and 700 °C two bcc + one hcp (550 °C with weaker residual matrix peaks); 700 °C series: 2.5 h major + minor (Ta–Nb-rich) bcc by XRD, small Ta–Nb-rich and Hf–Zr-rich precipitates by APT, ~3.23 vol.% grain-boundary precipitates; 96 h ~41.2 vol.% (grain-boundary lamellae + intragranular rounds), BCC1 3.447 Å, BCC2 3.323 Å, HCP a = 3.143, c = 5.042 Å; 192 h ~39.8 vol.%, coarsening and lamellar → spherical at boundaries; Zr–Hf-rich HCP in Burgers OR (SAED); CALPHAD restated (single bcc 1020–1200 °C; Nb–Ta bcc below 1020 °C; HCP from 800 °C); Senkov (800 °C / 2 h, two bcc) and Stepanov (800 °C / 100 h, HCP + BCC) restated; no oxygen; no mechanical test. Y21 abstract: two-bcc split 773–1073 K, hcp 773–973 K, ω 673 K, yield-stress rise at 873 K, dynamic hcp precipitation as cause. P1 (re-used): clean alloy single bcc at 900 °C / 1000 h under argon, vacuum-aged alloy decomposed; P1's restatement of C2.

ANALYSIS (mine, beside the sources)

The grades; the OQ3 partial answer (two edges: bcc split between 900 and 1000 °C in C2, hcp near 700–800 °C in Y21-abs); the 900 °C tension with P1 and its three readings; the restatement check; the speed comparison with Y4; design readings; the counting.

SPECULATIVE

§4 (Bridge A shapes).

Not claimed

No chemical correlate. No chemical stand-in for a theta role, a feature bundle or a slot. Not a joint field. Bridge A unrevised. No number read off a figure or XRD pattern. No oxygen level for C2's or Y21's alloy. No phase list at 900 °C. No strength or ductility for any C2 state. Nothing from the body of Yasuda et al. 2021, Stepanov et al. 2018, Schuh et al. 2018, Senkov et al. 2018 or Zhao et al. 2025 directly; nothing from the search-engine snippet of Y21. Li et al. 2025 opened in the 2026-11-05 evening note (Ti–Zr–Hf–Nb–Ta with Fe micro-alloying: a ductility window set by nano Hf₂Fe at grain boundaries), not in this file.


7. Verdict

Does an opened source place the upper edge of HfNbTaTiZr's intermediate-temperature instability? In part, yes: C2 anneals one starting state for 96 h at 550, 700, 900 and 1000 °C and finds two bcc + hcp at 550 and 700 °C, bcc peak splitting at 900 °C, and single bcc at 1000 °C ( STRONG as observed). With Y21's abstract (split to 1073 K, hcp to 973 K; WEAK), the band is two bands: the bcc split reaches between 900 and 1000 °C, the hcp about 700–800 °C (brackets, not pinned edges). Is it the clean alloy's edge? Unknown: oxygen is NONE in both labs, and C2's vacuum-tube 900 °C split stands against P1's clean-argon 900 °C stability ( HYPOTHESIS: pickup). OQ3 of the Nov 3 note is answered in part (brackets in one lab, agreement in kind from a second); OQ4 (Y21 primary) stays blocked. Bridge A unrevised.


v0 — 2026-11-04 PT, evening. Pointers added: corpus-reading-order row; CONCLUSIONS-v1-addendum paragraph; site-content-map (inventory, slug, near-ready, Path E page row); back-pointer at hfnbtatizr-nanohcp-873k-strengthening §5 OQ3 (+ footer). Quotes machine-checked against the captured text (lit/_pdfs/hea-phase-chen2019/check_quotes_chen.py). Speculation flagged. Bridge A lock unrevised. No joint field. Light update 2026-11-05 evening: §5 OQ5 answered by Ti–Zr–Hf–Nb–Ta with Fe micro-alloying: a ductility window set by nano Hf₂Fe at grain boundaries.

Corpus note: hfnbtatizr-unstable-band-edges-v0.md. The metallurgy is same-domain description from the source the note lists as opened: Chen et al. 2019 (Scripta Materialia 158: 50–56), the authors' accepted manuscript on OSTI (purl 1504430), read through its text layer; Tables 1–4 are cited but absent from that copy, so nothing is taken from them, and no number is read off an XRD pattern or micrograph. Quotes are verbatim and machine-checked. Yasuda et al. 2021 (MSEA 809: 140983) was blocked (publisher 403/400, no repository copy) and was not routed around; only its abstract, from OpenAlex, is used, graded WEAK. Neither paper measures oxygen, so no oxygen level is given. The temperature edges are brackets between tested temperatures, not measured transition points. The grades (STRONG / WEAK / NONE / HYPOTHESIS) and the comparisons between sources are analysis, not a declared correlate. The Bridge A section comes after the materials and is speculative. No chemical stand-in for a theta role or a slot. Bridge A unrevised. Not a joint field.