HfNbTaTiZr after hot isostatic pressing: a Zr–Hf-rich HCP phase and no measurable tensile elongation (oxygen not measured) — materials scout,
What’s claimed and how well supported
- Labels on this page
- STRONG ×18 HYPOTHESIS ×10 WEAK ×4 SPECULATIVE ×6 NONE ×8
- Strongest label used
- STRONG
- Main caveat (quoted)
- The Bridge A section comes after the materials and is ◆ SPECULATIVE.
Counted automatically from the labels printed on this page. Counts are a reading aid, not a grade of the page.
Terms on this page (10), plain-language definitions
- HCP
- Hexagonal close-packed — fewer primary slip systems; Mg, Ti, Zn often anisotropic.
- Dopant
- Intentional dilute impurity meant to tune electronic/optical/catalytic behavior without replacing the host as majority phase.
- Solute
- Intentional minority species dissolved in the host (alloying addition).
- Grain boundary
- Interface between crystals in a polycrystal; barriers in Hall–Petch strengthening.
- Precipitate
- Second-phase particle that forms (often on aging) and blocks dislocations.
- BCC
- Body-centered cubic — Fe/steel common; plasticity more temperature-sensitive.
- Solid solution
- Solute atoms dissolved into the host lattice (substitutional or interstitial) without a separate precipitate phase.
- Dislocation
- Line defect enabling plastic slip at realistic stresses; edge vs screw are the two classic geometries.
- Host (matrix)
- Majority element/phase whose lattice dominates the material.
- Valency (ling.)
- Arity: how many actants a predicate takes; formal vs semantic valency can diverge.
Definitions quoted from the Chem for linguists primer glossary.
Date: 2026-11-02 PT (weekday research push, evening)
Status: Materials scout. The metallurgy is same-domain description from the source opened below (REAL inside physical metallurgy). Grades and cross-source comparisons are my analysis. The Bridge A section comes after the materials and is SPECULATIVE. Not a correlate. Not a joint field.
Audience: Grant (syntax/semantics; less chemistry). End goal: designing new metal alloys. Takes up open question OQ4 ("Ageing and ductility") of Oxygen in HfNbTaTiZr: measured 0.27 vs 3.24 at.%, stability on ageing §5, in part: the first opened tensile test on the Ta-bearing equiatomic alloy in a state that holds a second (HCPHexagonal close-packed — fewer primary slip systems; Mg, Ti, Zn often anisotropic.) phase. The best target for that question, Zhao et al. 2025 (Acta Mater. 298: 121400), is still blocked here (§1.2).
Source, stated plainly: one paper opened in full, Larianovsky, Katz-Demyanetz, Eshed & Regev 2017 (Materials 10: 883, CC BY), as the Europe PMC full-text XML. It casts equiatomic Ta20Nb20Hf20Zr20Ti20 two ways (gravity and suction-assisted casting), hot isostatically presses (HIP) both, and tests them in tension, compression and creep. It reports no oxygen, nitrogen or carbon analysis. So this note is about a second phase and tensile brittleness in the same nominal alloy as last session's note, not about an oxygen dose.
Vocabulary lock kept: Hf, Nb, Ta, Ti, Zr are principal elements, not dopantsIntentional dilute impurity meant to tune electronic/optical/catalytic behavior without replacing the host as majority phase. (Doping vs alloying vocabulary). Oxygen is an interstitial soluteIntentional minority species dissolved in the host (alloying addition).; in this source it is not measured at all.
Does not: claim that an oxygen atom, a precipitateSecond-phase particle that forms (often on aging) and blocks dislocations., a phase, a grain boundaryInterface between crystals in a polycrystal; barriers in Hall–Petch strengthening. or a fracture mode is an argument, operator, slot, feature bundle or theta role; supply a chemical stand-in for a theta role; invent numbers or quotes; read numbers off figures or XRD spectra; claim an oxygen level for the source's alloy; revise Bridge A.
Why this note. The Oct 30 note found that equiatomic HfNbTaTiZr at a measured 3.24 at.% O loses its single bcc state on long holding at 900 °C (Poulain et al. 2024, P1), and left open what a second phase of that kind does to tensile ductility (OQ4: NONE). P1 has no mechanical test; the paper that has one (Zhao et al. 2025) is blocked. Tonight opens the one open full text found that pulls this exact alloy in tension in a state with a Zr–Hf-rich HCP phase.
The case, in plain words. Cast bars of the classic five-metal alloy (equal shares of tantalum, niobium, hafnium, zirconium, titanium), one set cooled in the mould by gravity casting, one set sucked into the mould. Each is then squeezed hot under gas pressure (HIP, 1230 °C, 152 MPa, 4 h) to close pores. Before HIP the bars are one phase; after HIP a second, Zr–Hf-rich phase appears. Pulled at room temperature, the bars break with no stretch the machine can detect; squeezed, they are strong.
What is new (one sentence). In equiatomic Ta20Nb20Hf20Zr20Ti20, single phase as cast but carrying a Zr–Hf-rich HCP phase after HIP at 1230 °C (evenly dispersed after gravity casting, mostly at grain boundaries after suction casting; STRONG as observed, SEM + XRD + EDS), five room-temperature tension bars broke at a maximum stress of 669–749 MPa with elongation "below the machine’s detection limit" and inter-crystalline fracture "without any plastic deformation" ( STRONG as measured, two casting routes), while compression yield was 1350–1888 MPa ( STRONG as measured); the paper does not measure oxygen, so whether oxygen drove the HCP phase or the brittleness is NONE in this source, and reading it as oxygen-driven (from P1's statement that this alloy's phase-stability discrepancies "may be related to the presence of oxygen") is a HYPOTHESIS; the cause of the brittleness is NONE (the authors say "further research is still required in order to understand the failure mechanism"), and that the HCP phase is that cause is a HYPOTHESIS.
1. Sources
1.1 Opened this run
| Key | Source | How read | Used for |
|---|---|---|---|
| L3 | Larianovsky, Katz-Demyanetz, Eshed & Regev, "Microstructure, Tensile and Creep Properties of Ta20Nb20Hf20Zr20Ti20 High Entropy Alloy", Materials 10(8) (2017) 883, doi:10.3390/ma10080883 (CC BY 4.0; PMC5578249) | Europe PMC REST full-text XML (/PMC5578249/fullTextXML, HTTP 200), tags stripped to paragraphs and table cells → lit/_pdfs/hea-tension-larianovsky2017/larianovsky2017-pmc5578249.txt (XML kept beside it) |
Materials and route, phases before and after HIP (Table 1 EDS), hardness, tension and compression (Table 2), fracture, creep, the authors' mechanism, the restated Senkov et al. cold-rolled tensile numbers |
| (re-used) | P1 (Poulain et al. 2024) and Z1-abs (Zhao et al. 2025 abstract), lit/_pdfs/hea-oxygen-hfnbtatizr/; L2 (Lei et al. 2020), lit/_pdfs/hea-oxygen-lei2020/ |
Captures only | Contrast in §3 |
Weakness of the copy, stated plainly. The XML gives the prose and the tables; the SEM images, XRD spectra (Fig. 2) and fractographs (Figs. 3–6) are images I did not look at, so no number in this note comes from a figure. The XRD peak positions are given in the prose and are not used. Table 2 lists the tension values without saying which column each sits in; from the prose ("the maximum stress measured is given in Table 2") and the column order, I read the five tension values as σmax and the six compression values as σy. That column reading is mine ( WEAK as a table parse; the prose supports it).
What the source does not report, stated plainly. No oxygen, nitrogen or carbon content of the alloy (the only oxygen in the methods is that molten titanium "was used as a getter for residual oxygen, nitrogen, and hydrogen"). No HIP gas or cooling rate in the methods; the slow cooling appears only in the discussion as part of the authors' explanation. No grain size number. No tensile test before HIP. No count of creep specimens beyond the two tests named.
Independence, stated plainly. L3 (a group thanking the Israel Institute of Metals in its acknowledgments) shares no author with P1/Z1 (Laplanche, Li et al.) or L2/J1 (Lu, Wu, Lei et al.). It is independent of both, on the same nominal alloy as P1.
1.2 Not opened (do not treat as read)
- Zhao et al. 2025 body (Z1, Acta Mater. 298: 121400, CC BY): retried tonight. KIT repository (publikationen.bibliothek.kit.edu/1000186286): curl from the box failed at TLS again (exit 35); the fetch tool returned the landing page and abstract only, no file link; doi.org via the fetch tool returned HTTP 500 (on Oct 30 ScienceDirect returned a bot block, HTTP 403). OpenAlex still lists
any_repository_has_fulltext: falseand nopdf_url. Not routed around. Its tensile numbers are not in this note. - MDPI PDF of L3 (mdpi.com/1996-1944/10/8/883/pdf): HTTP 403 (an access-denied page) to curl; the PMC article page returned 403 to the fetch tool. Not needed: the Europe PMC XML is the same CC BY article text.
- Senkov & Semiatin 2015 (J. Alloys Compd. 649: 1110–1123; L3 ref. [7], P1 ref. [3]): not opened. Its cold-rolled tensile numbers appear here only as L3 restates them.
- Senkov et al. 2011, 2012 (L3 refs. [2], [3]); Lin et al. (L3 ref. [9]); Chen et al., Stepanov et al., Yang et al., Maiti et al. (P1 refs. [27]–[30]): titles or restatements only.
2. Sourced materials (L3, with P1 for contrast)
2.1 Alloy and route (L3)
- Melting: "prepared by vacuum arc melting of the nominal mixtures of the corresponding elements"; purities "Ta, Nb, Hf, Zr, and Ti were 99.9%, 99.9%, 99.7%, 99% and 99.7%, respectively"; "Melting was conducted in a high-purity argon atmosphere"; buttons "re-melted four times".
- Casting: bars "9 mm in diameter and 85 mm in length"; one group by "gravity casting", the other "cast by applying suction by means of a vacuum pump".
- HIP: "the bars underwent HIP at 1230 °C and 152 MPa for 4 h", then radiography for porosity. Tension, compression and creep specimens "were prepared from the HIP’ed bars by machining".
- Composition (Table 3, as cast, at.%): Ta 20.4, Nb 20.1, Hf 20.6, Zr 20.7, Ti 18.2. No interstitials listed.
2.2 Phases before and after HIP (L3)
- Before HIP: "both materials were single phased before undergoing HIP"; XRD "correspond to single-phase NbTaTi-based BCCBody-centered cubic — Fe/steel common; plasticity more temperature-sensitive. material".
- After HIP: "a darker phase is discernible inside the bright matrix"; identified (EDS + XRD) as "a roughly equimolar solid solutionSolute atoms dissolved into the host lattice (substitutional or interstitial) without a separate precipitate phase. of ZrHf" with HCP structure beside "a solid solution of NbTaTi".
- Where it sits: "the dark phase is evenly dispersed in the matrix of the gravity-assisted casting, while in the case of the suction-assisted casting it is concentrated mostly at the grain boundaries".
- EDS (Table 1, at.%), darker phase: gravity — Ti 10.88, Zr 48.79, Nb 4.00, Hf 33.26, Ta 3.07; suction — Ti 8.52, Zr 57.38, Nb 3.12, Hf 28.51, Ta 2.47. Matrix after HIP: gravity — Ti 20.30, Zr 21.42, Nb 27.35, Hf 10.78, Ta 20.15; suction — Ti 20.13, Zr 21.58, Nb 27.70, Hf 10.92, Ta 19.67. (EDS does not measure oxygen reliably and none is listed.)
- Authors' mechanism: when the HIP cycle ends "and the alloy is left to cool at a very slow rate inside the furnace the HCP phase forms out of the original BCC phase, either by a eutectoid reaction or by precipitation"; as cast, rapid cooling gives "a supercooled BCC phase"; "further research is still required in order to confirm the proposed mechanism".
2.3 Hardness (L3)
- Before HIP: "323.5 ± 6.5 HV" (gravity), "330.2 ± 9.8 HV" (suction). After HIP: "437.2 ± 11.6 HV and 509.1 ± 13.5 HV" (gravity, suction). Ten indents each.
- Authors' reading: the rise "can be related to the appearance of the secondary HCP phase and its influence on dislocationLine defect enabling plastic slip at realistic stresses; edge vs screw are the two classic geometries. mobility, similarly to precipitation hardening".
2.4 Tension, compression, fracture, creep (L3, after HIP)
- Tension (Table 2, σmax, MPa): gravity 669, 749; suction 694, 708, 678. "The elongation to fracture under tension was below the machine’s detection limit and therefore could not be measured"; yield and ultimate could not be told apart, so "the maximum stress measured is given in Table 2".
- Compression (Table 2, σy, MPa): gravity 1380, 1350, 1749; suction 1725, 1684, 1888. "σy under compression is almost as twice as high as the maximum stress under tension".
- Fracture: "the fracture is inter-crystalline in both cases, without any plastic deformation"; in the suction casting it "is accompanied by intergranular cracking, which is most intensive at the center of the specimen".
- Creep at 982 °C (gravity cast): under 200 and 120 MPa, "Both failed after short periods of time of 15 and 90 min, respectively"; the creep fracture surface "is contaminated with oxidation products, mainly at the near-surface regions of the sample".
- Authors' conclusion: "both materials are extremely brittle under tension"; failure mechanism not settled.
2.5 Restated, not read: the wrought alloy in tension (L3 citing Senkov et al. [7])
- "Senkov et al. [7] reported that the 86.4% cold-rolled material showed true tensile strength of 1295 MPa and tensile ductility of 4.7%"; annealing led "to the formation of fine second-phase precipitates which could not be characterized by them [7]".
- P1 (Oct 30) cites the same paper (its ref. [3]) for: "This alloy is one of the few BCC HEAs that is ductile and malleable at room temperature [3]."
2.6 P1 on why reports disagree (re-used capture)
- P1 lists conflicting phase-stability reports for this alloy (single phase above 900 °C in one study; "secondary phases up to 1450" °C in another) and states: "The first objective of the present work is to show that these discrepancies may be related to the presence of oxygen (O) that strongly affects the phase stability of the HfNbTaTiZr HEA." P1 does not cite L3.
- P1's own 3.24 at.% O alloy, "annealed at 1200" °C "for 48 h followed by water quenching", was "a single-phase BCC solid solution" (Oct 30 note §2.1).
3. Grades and analysis
| Claim | Grade | Basis |
|---|---|---|
| As cast (both routes) the alloy is single bcc | STRONG as observed (SEM + XRD) | L3 |
| After HIP at 1230 °C / 152 MPa / 4 h a Zr–Hf-rich HCP phase is present beside a Nb–Ta–Ti bcc matrix | STRONG as observed (SEM + XRD + EDS, both routes) | L3 |
| HCP evenly dispersed (gravity) vs mostly on grain boundaries (suction) | STRONG as observed | L3 |
| HIP raises hardness ~324–330 → ~437–509 HV | STRONG as measured (ten indents each) | L3 |
| Room-temperature tensile elongation of the HIP'd alloy is below detection; fracture inter-crystalline, no plasticity | STRONG as measured (five bars, two routes) | L3 |
| Tension σmax 669–749 MPa vs compression σy 1350–1888 MPa | STRONG as measured (column reading of Table 2 WEAK; prose supports) | L3 |
| Slow furnace cooling after HIP formed the HCP phase | WEAK (authors' reading, untested; cooling not given in methods) | L3 |
| The HCP phase caused the tensile brittleness | HYPOTHESIS (authors do not claim it; mechanism "further research"); the cause is NONE as sourced | L3 |
| Oxygen content of L3's alloy | NONE (not measured) | L3 |
| Oxygen drove L3's HCP phase or its brittleness | HYPOTHESIS (P1 says discrepancies "may be related" to oxygen; not tested on L3's material) | P1 + L3 |
| The same nominal alloy is ductile in a wrought single-bcc state (4.7% after 86.4% cold rolling) | WEAK here (restated by L3 from an unopened paper; P1 agrees in words) | L3 restating Senkov & Semiatin 2015; P1 |
Answer to OQ4 (analysis), in part. OQ4 asked whether losing single bcc cuts tensile elongation. L3 gives the first opened tensile data for equiatomic HfNbTaTiZr in a state that has lost single bcc: elongation below detection, brittle inter-crystalline fracture ( STRONG as measured). It does not isolate the cause: there is no single-bcc tension bar from the same casting to compare with, oxygen is unmeasured, and the authors leave the failure mechanism open. So: a two-phase (bcc + Zr–Hf-rich HCP) HfNbTaTiZr can be fully brittle in tension ( STRONG as an observed case); the HCP phase is why ( HYPOTHESIS). The ageing route of OQ4 (900 °C, P1; 500 °C, Z1) is not the HIP route here, so the OQ4 answer for aged material stays NONE.
Boundary coverage is not needed for this brittleness (analysis). P1 found continuous HCP on grain boundaries of its aged 3.24 at.% O alloy and the Oct 30 note flagged that as a likely weak point. In L3, the gravity casting, with HCP "evenly dispersed in the matrix", was as brittle in tension as the suction casting, with HCP "concentrated mostly at the grain boundaries" (σmax 669–749 vs 678–708 MPa; both below detectable elongation). So in L3 a boundary layer is not required for zero tensile elongation ( WEAK: two routes, a handful of bars, other differences between castings such as grain-size spread, and an unknown interstitial content).
Oxygen as the hidden variable (HYPOTHESIS). Three facts sit side by side. (1) P1: in clean argon the 0.27 at.% O base stays single bcc at 900 °C for 1000 h, but oxygen pickup in vacuum makes the same HCP + Nb–Ta bcc split ( STRONG, Oct 30). (2) P1: even at 3.24 at.% O, 1200 °C / 48 h with a water quench gives single bcc ( STRONG). (3) L3: after 1230 °C HIP, by the authors' account cooled slowly, a Zr–Hf-rich HCP phase is present; the Zr used was 99% pure; no interstitial was measured. Fact (2) fits the authors' slow-cooling reading (high temperature alone need not split the alloy if it is quenched). Fact (1) shows oxygen can drive the same split at lower temperature. Which one acted in L3, or both, is not decidable from the opened sources. Calling L3's HCP oxygen-driven would be inventing a hostMajority element/phase whose lattice dominates the material. fact; it is a HYPOTHESIS only.
Compression does not certify tension (analysis). In one alloy state, compression yield is about twice the tensile maximum, and the bars that yield at 1350–1888 MPa in compression snap in tension with no measurable plasticity ( STRONG within L3). Earlier notes leaned on compression for a ductility-free signal (İroç 2022 thesis: no fracture to 35% compressive strain, Oxygen added on purpose: a dose window in refractory high-entropy alloys). L3 is a sourced reason not to read a compressive test without fracture as tensile ductility in this family ( STRONG as a caution; a different alloy and state from İroç's).
Same mix, opposite outcomes across states (analysis, across sources). As cast + HIP (L3): brittle in tension, two phases. Cold rolled 86.4% (Senkov et al. as restated by L3): 4.7% tensile ductility. Lei et al. 2020's Ta0.5Nb0.5HfZrTi (different composition, single bcc, as cast, measured 0.377 and 2.241 at.% O): ~10.8% and ~20% (Oct 29). The ductility of this family is a property of composition + interstitials + process state + phase content, not of the nominal formula ( STRONG as a contrast of observed cases; the share each factor takes is NONE).
Design-relevant reading (analysis). (1) Check the phase state after any HIP or slow cool before relying on tensile ductility in HfNbTaTiZr-type alloys; L3 shows HIP can leave a fully brittle two-phase state ( STRONG as one observed case). (2) Measure O, N, C in any such study; L3's lack of it is what blocks reading it against P1 ( HYPOTHESIS for practice). (3) A quench after HIP, or a post-HIP solution anneal and quench, is the obvious test of the authors' slow-cooling reading ( HYPOTHESIS; not tested in any opened source). (4) Test in tension, not only compression.
Counting rule. Only contradicting data count. L3 does not contradict L2 (different composition, unknown oxygen, different state) or P1 (P1 has no tension test; L3 shows a second phase where P1's clean alloy at 900 °C had none, but L3's oxygen and cooling are not known, so no contradiction can be scored). L3 does not contradict the wrought ductility that P1 and L3 both cite; it is a different state. No source counted twice; L3 is independent of both earlier groups.
SPECULATIVE Cross-domain section. Open after the materials.
4. Bridge A — SPECULATIVE (after the materials)
Bridge A (locked): doping concentration windows and over-doping ↔ valencyArity: how many actants a predicate takes; formal vs semantic valency can diverge., argument saturation and over-arity. Shapes only:
- Same formula, different state, opposite outcome. One nominal mix is ductile in one processed state and fully brittle in another. Shape: whether a combination fits is not settled by the list of what is in it. Shape only.
- One test does not certify another. The same bars pass a squeeze test with high numbers and fail a pull test at once. Shape: a fit measured one way need not hold when the load is taken another way. Shape only.
- An unmeasured amount. L3 never measures the interstitial content, so no window edge can be placed from it at all. Shape: without the count of what was added, there is no window to read. Shape only.
- Still continuous. Hardness, stresses and at.% are continuous amounts; the lock "continuous wt% ≠ discrete arity" holds; nothing here counts slots.
Bridge A pressure: none that forces revision. Bridge A unrevised. No chemical stand-in for a theta role, slot or feature bundle; not a correlate; not a joint field. Merge/Agree not involved. No Navajo remark tonight.
5. Open questions
- Interstitials in a HIP'd brittle HfNbTaTiZr. A study that HIPs this alloy and measures O, N and C (gas fusion or hot extraction), so L3's HCP phase can be read against P1. None opened.
- HIP plus quench vs HIP plus slow cool. Same casting, same HIP, two cooling paths, then tension. Tests the authors' slow-cooling reading.
- Single-bcc vs two-phase tension in one batch. A tension bar of the same material before and after the HCP phase forms (by ageing or slow cooling), which is what OQ4 of the Oct 30 note actually needs. Z1 (Zhao et al. 2025) is the nearest; its body is still blocked here. → Partly answered, in compression only, in HfNbTaTiZr at 873 K: nanoscale hcp and a stress rise in one batch (compression only) (2026-11-03): in one batch of HfNbTaTiZr at 873 K, an 1800 s hold forms a spinodal bcc1/bcc2 split and <10 nm hcp and the flow stress rises, while a 120 s hold suppresses the hcp and the rise (Yasuda et al. 2025; STRONG as a same-batch contrast); oxygen not measured (NONE); tensile elongation with the nano-hcp stays NONE.
- The primary wrought numbers. Senkov & Semiatin 2015 (J. Alloys Compd. 649) for the cold-rolled 4.7% and the annealed states, opened rather than restated.
- Carried: OQ1–OQ3 of Oxygen in HfNbTaTiZr: measured 0.27 vs 3.24 at.%, stability on ageing (tensile ceiling in a Ta-bearing alloy; where the 900 °C breakdown starts; the swaging crack); OQ2–OQ4 of Oxygen in a Ta-bearing five-element alloy: one measured tensile pair; OQ2 of Where added oxygen stops helping ductility: a tensile ladder in Ti–Zr–Nb; OQ1/OQ4 of Oxygen added on purpose: a dose window in refractory high-entropy alloys.
6. Separation
SOURCED (inside metallurgy)
L3: equiatomic Ta20Nb20Hf20Zr20Ti20 (as cast Ta 20.4, Nb 20.1, Hf 20.6, Zr 20.7, Ti 18.2 at.%; Zr 99% pure; interstitials not measured), vacuum arc melted under Ar with Ti getter, gravity vs suction cast, HIP 1230 °C / 152 MPa / 4 h; single bcc before HIP; Zr–Hf-rich HCP after HIP (evenly dispersed vs mostly on boundaries); hardness ~324–330 → ~437–509 HV; tension σmax 669–749 MPa with elongation below detection and inter-crystalline fracture without plasticity; compression σy 1350–1888 MPa; creep at 982 °C failed in 15 and 90 min with oxidation products near the surface; authors' slow-cooling mechanism and open failure mechanism; Senkov et al. cold-rolled 1295 MPa / 4.7% as restated. P1 (re-used): discrepancies "may be related to the presence of oxygen"; 3.24 at.% O single bcc after 1200 °C / 48 h + water quench.
ANALYSIS (mine, beside the source)
The grades; the Table 2 column reading; the OQ4 partial answer; the boundary-coverage remark; the oxygen-as-hidden-variable reading (HYPOTHESIS); the compression-vs-tension caution; the cross-state contrast; design readings; the counting.
SPECULATIVE
§4 (Bridge A shapes).
Not claimed
No chemical correlate. No chemical stand-in for a theta role, a feature bundle or a slot. Not a joint field. Bridge A unrevised. No number read off a figure or an XRD spectrum. No oxygen level for L3's alloy. No claim that oxygen caused L3's HCP phase or brittleness. No claim that the HCP phase caused the brittleness. Nothing from the body of Zhao et al. 2025 or from Senkov & Semiatin 2015 directly. No tensile ceiling claimed for any oxygen level.
7. Verdict
Does an opened source put equiatomic HfNbTaTiZr in tension in a state that has lost single bcc? Yes, one: L3, after HIP, with a Zr–Hf-rich HCP phase. What happens? It breaks with no measurable elongation, inter-crystalline, at 669–749 MPa, while yielding at 1350–1888 MPa in compression ( STRONG as measured). Is it oxygen? Unknown ( NONE measured; HYPOTHESIS via P1). Is it the HCP phase? HYPOTHESIS; the cause is NONE as sourced. OQ4 of the Oct 30 note is answered in part (a two-phase state can be fully brittle in tension), not for aged material and not for any oxygen dose. Bridge A unrevised.
v0 — 2026-11-02 PT, evening. Pointers added: corpus-reading-order row; CONCLUSIONS-v1-addendum paragraph; site-content-map (inventory, slug, near-ready, Path E page row); back-pointer at hfnbtatizr-oxygen-ageing-stability §5 OQ4 (+ footer). Quotes machine-checked against the captured text (lit/_pdfs/hea-tension-larianovsky2017/check_quotes_larianovsky.py). Speculation flagged. Bridge A lock unrevised. No joint field. 2026-11-03: OQ3 partly answered (compression only) in hfnbtatizr-nanohcp-873k-strengthening-v0.md (back-pointer in §5).
Corpus note: hfnbtatizr-hip-tensile-brittleness-v0.md. The metallurgy is same-domain description from the source the note lists as opened: Larianovsky et al. 2017 (Materials 10: 883, CC BY 4.0), as the Europe PMC full-text XML read as text; SEM images, XRD spectra and fractographs were not looked at, so no number is read off a figure. Quotes are verbatim and machine-checked. The paper measures no oxygen, nitrogen or carbon, so no oxygen level is given for its alloy; reading its HCP phase as oxygen-driven (via Poulain et al. 2024) is a hypothesis, as is the HCP phase being the cause of the brittleness. Senkov et al.'s cold-rolled tensile numbers appear only as this paper restates them. Zhao et al. 2025 is still blocked and was not routed around. The grades (STRONG / WEAK / NONE / HYPOTHESIS) and the comparisons between sources are analysis, not a declared correlate. The Bridge A section comes after the materials and is speculative. No chemical stand-in for a theta role or a slot. Bridge A unrevised. Not a joint field.